E3 9W LED Warning Light Head | TIR Lens

The E3 is the entry point into this range of surface mount warning light heads, built around three 3W LEDs behind a TIR (total internal reflection) lens for a 9W LED array in a compact 117mm housing. It signals vehicle presence on traffic control, civil, utility and fleet vehicles, plant and machinery, and is supplied as a single fixed output per unit: white, red or blue.

The E3 surface mounts through two screw fixing points, one in each end flange, 104mm between centres. Drill two holes in the mounting surface and fix with two screws. It suits grille surrounds, bull bars, guards, tray and body rails, headboards and rear body panels. Confirm mounting hardware and wiring with your auto electrician for your specific vehicle and application.

Output runs across 19 selectable flash patterns at a flash rate of 1 to 4Hz, and the head holds the last pattern selected when power is removed, so a fitted vehicle comes back on in the same setting. Up to 19 heads synchronise together, enough for a full front, side and rear set running as one system. Input is 10 to 30V DC, covering 12V and 24V vehicles and plant with the one part, at a maximum draw of 7W, the lowest in the range.

Wiring runs on four 20 AWG cores: red for +12 to 24V DC power through a 3A fuse, black for chassis ground, white to set the head into flash group one or group two for simultaneous or alternating operation, and yellow for pattern selection and synchronisation. Wiring should be carried out by a qualified auto electrician.

The housing is polycarbonate, sealed to IP65 and rated for ambient temperatures from -20 to +65 degrees. LED lifespan is rated at 100,000 hours. Overall size is 117 x 45 x 24mm.

Supplied product data lists ECE R65 XB1 00 0025 and ECE R10 03 12468. Vehicle lighting requirements vary by vehicle type, registration category and jurisdiction, so confirm the requirements that apply to your vehicle and use.

The E3 is the smallest and lowest draw head in this range. The E4 12W LED warning light head is the four-LED version of the same wedge housing, longer at 146mm, and the H4 12W LED warning light head is a four-LED TIR head in a 120mm oval housing. For wide angle reflex output instead of forward-directed TIR, see the C4 and the 27W C9. The X6 18W LED warning light head gives six LEDs and a 180 degree viewing angle from a compact 90mm housing, and is the head UAGS continues to stock in depth across amber, white, red and blue. For amber warning output on traffic control and civil vehicles, see the UAGS-branded U30-6, U30-12A and U31 light heads.

• 3 x 3W LEDs (9W Array): Each LED behind its own optical cell.
• TIR Optics: Total internal reflection lens directs output forward rather than scattering it.
• Lowest Draw In The Range: 7W maximum, useful where several heads share a circuit.
• 19 Flash Patterns: Selected through the yellow wire, at a flash rate of 1 to 4Hz.
• Pattern Memory: Holds the last pattern selected when power is removed.
• Synchronisation Up To 19 Heads: Enough for a full front, side and rear set running as one system.
• Two Flash Groups: The white wire sets each head to group one or group two for simultaneous or alternating flash.
• 10-30V DC: Suits 12V and 24V vehicles and plant with one part.
• Surface Mount: Two screw fixing points, one in each end flange, 104mm between centres.
• Compact 117mm Housing: Polycarbonate, 117 x 45 x 24mm.
• IP65 Sealed: Rated -20 to +65 degrees.
• 100,000 Hour LED Lifespan.
• Approvals: ECE R65 XB1 00 0025 and ECE R10 03 12468.
• 20 AWG Wiring Loom.

UAGS Warning Light Warranty - 3-Year Limited Coverage
This product is imported and branded by UAG Services Pty Ltd, which acts as the manufacturer of this item for warranty purposes. It is covered by a 3-year limited warranty against defects in materials and workmanship under normal use.

This warranty does not cover normal wear and tear, weathering or UV degradation, accidental or impact damage, water ingress caused by damaged seals not reported at delivery, incorrect or unauthorised installation, unauthorised modification, or use outside the product's stated voltage and operating conditions. Installation should be carried out by a qualified auto electrician; damage caused by DIY wiring is not covered.

To make a warranty claim, contact UAG Services Pty Ltd (Gate 2, 7 Royan Place, Bayswater North VIC 3153) at sales@uags.com.au or (03) 8750 0926 with your order reference, a description of the fault and photos of the product. Claims are subject to inspection and approval. Where a defect is confirmed, UAG Services Pty Ltd will repair, replace or refund the product at its discretion. Return shipping costs are handled in accordance with the UAGS Returns Policy unless otherwise required under Australian Consumer Law.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is provided in addition to these rights and does not limit or exclude them.