Traffic Control Equipment Specialist

Multi Message Sign Panels Low prices on 100's of items

How to Choose a Traffic Control Racking Cage: 7 Things to Check Before You Buy

By The UAGS Team  •   8 minute read

White traffic control ute with a UAGS racking cage and B-Class arrow board, outside the UAGS depot in Bayswater North

To choose a traffic control racking cage, start with what the crew carries, then check it against your tray. List the multi-message frames, corflute panels, frame legs, bollards, bats and arrow board the vehicle needs every day, measure the tray length and width, and decide whether bollards travel in the cage or in the tray space beside it. That tells you whether a standard design fits or whether the cage should be designed around your vehicle. UAGS has more than 50 cage designs and draws every cage in-house in CAD, so the answer is rarely limited to what you see in a catalogue.

This guide walks through the seven checks we go through with every customer before a cage is built, plus what a full traffic control vehicle fit-out involves.

In this article

What is a traffic control racking cage?

A racking cage is a steel frame that mounts on a ute or truck tray and holds traffic control equipment in fixed sections. Sign panels and multi-message frames slide into their own housings, frame legs sit in a leg section, stop/slow bats have their own compartment, and the arrow board usually mounts on top. Every piece of gear has a set place, so crews unload and reload in the same order on every job, and nothing is loose on the tray.

A cage also helps you restrain the load. Equipment on a work vehicle still has to be properly secured for travel, and the National Transport Commission's Load Restraint Guide sets out the performance standards loads need to meet.

Labelled layout of the UAGS Design 7 traffic control racking cage showing where frames, corflute panels, legs, bats, cone bars and the arrow board sit
Design 7 layout: every item has a fixed section. Equipment shown is sold separately.

1. What does the crew carry every day?

Start with the equipment list, not the cage. Write down what goes on the vehicle for a typical shift:

  • How many multi-message frames, and which panel sizes (600 x 600mm, 1200 x 300mm or others)
  • How many frame legs
  • Bollards and bases, and how many
  • Stop/slow bats, Temporary Hazard Markers and cone bars
  • Whether the vehicle runs a vehicle-mounted arrow board
  • Small items such as flags, barrier tape and clips

As a reference point, our standard front section holds 25 multi-message frames, two 200mm sections of 600 x 600mm panels, one 200mm section of 1200 x 300mm panels, 60 Y-frame legs, two stop/slow bats, four Temporary Hazard Markers and more than 10 cone bars. If your list is close to that, a standard design is likely to suit. If it is quite different, the cage should be designed around your list.

Traffic control ute fitted by UAGS, loaded with Temporary Hazard Markers, sign frames, cone bars and cones
A fitted ute loaded for the day, with every item in its own section.

2. How big is your tray?

Measure the tray's usable length and width, inside any headboard, toolboxes or fittings. The cage has to fit the tray, and you still need room for anything that rides beside it, such as cones and bollard bases.

Our three standard designs give you a feel for the sizes involved:

Design Length Width (overall / footprint) Height Bollard storage
Design 7 1600mm 1650mm / 1550mm 1215mm None
Design 21 1980mm 1650mm / 1550mm 1215mm Up to 10 T-top stems and 9 bases
Design 16 2025mm 1650mm / 1550mm 1215mm 30 T-top stems (bases in tray space)

The 1650mm overall width includes the arrow board mounting bars and the stop/slow bat holder. The cage itself sits on a 1550mm footprint. If your tray is a different size, that is not a dead end. It is the most common reason we design a cage from scratch.

UAGS Design 21 racking cage with overall dimensions of 1980mm long, 1650mm wide and 1215mm high
Design 21 with overall dimensions. Equipment shown is sold separately.
Light truck fitted with a UAGS racking cage and arrow board on the tray
UAGS cages suit light truck trays as well as utes.

3. Do bollards need to travel in the cage?

Bollards decide the length of the cage more than anything else. There are three common answers:

  • No bollards, or only a few. A shorter cage such as Design 7 leaves more tray space for cones.
  • A small set with their bases. Design 21 adds a single-row hanger for up to 10 T-top bollards and three compartments holding 9 bases, so the bollards and bases stay together.
  • Bollard work every day. Design 16 adds a mesh-fronted section for 30 T-top bollard stems and an enclosed storage box, with the bases carried in the tray space.

If none of those match your mix, we can change the bollard section or design a different layout.

Custom UAGS racking cage with a hinged mesh section, stacking posts on the tray and an arrow board and beacon on top
A custom layout with a hinged mesh section and stacking posts on the tray.
UAGS Design 21 traffic racking cage loaded with bollards, bases, frames and an arrow board
Bollards and bases on the cage
Racking Cage Design 21

Design 7 front section plus a hanger for up to 10 T-top bollards and compartments for 9 bases.

4. How will the arrow board and lights mount?

Most traffic control vehicles run a B-Class arrow board, and the cage is usually what carries it. Our standard designs fix the arrow board on two 1600mm mounting bars across the top of the cage, and our arrow boards come with their beacon brackets already attached.

Plan the rest of the lighting at the same time: beacons, light bars and work lights all need mounting points and wiring runs, and it is much easier to allow for them in the cage design than to add them later. Our amber beacon buying guide covers choosing beacons.

Double sided B Class LED arrow board on its mounting brackets
Mounts on the cage
B Class LED Arrow Board Double Sided

Vehicle-mounted B Class arrow board for display to the rear and front of the vehicle.

5. Standard design or a cage designed for you?

The three designs on our website are a starting point, not the full range. We have more than 50 cage designs, and every one is drawn in-house in CAD. When you send us your vehicle, tray size and equipment list, we either select a design that already suits or design a new cage to meet your requirements.

We consult with you through the design. If you want something specific, such as a different panel section, a bollard hanger, a storage box or a particular access point, we work it into the layout. You see the CAD drawing before the cage is built, so you know exactly what you are getting and can change it while it is still on screen.

UAGS Design 7 racking cage modelled in AutoCAD, showing the steel frame, arrow board, cone bars and cones
Every UAGS cage is drawn in-house in CAD before it is built.

Once the layout is agreed, you get a drawing like the one below, showing the material notes and the equipment in place. This one is Variant 03 of Design 16, which shows how a standard design can be changed to suit a different setup.

UAGS CAD drawing of Cage 16 Variant 03 with equipment installed, showing material notes and title block
A UAGS customer drawing: Cage 16 Variant 03 with equipment installed.
UAGS Design 7 traffic racking cage loaded with frames, panels, legs and an arrow board
Our most popular design
Racking Cage Design 7

1600mm long, 25 multi-message frames, 60 legs and a B-Class arrow board on 2 x 1600mm bars.

6. Who fits the rest of the vehicle?

A cage is usually one part of a bigger job. UAGS fits the whole vehicle in-house at our Bayswater North depot in Victoria: the racking cage, B-Class arrow board, beacons and light bars, work lights, dual battery system, wiring and UHF radio, plus the signs, frames, bollards and cones to load it.

We work through each product with you, so the vehicle is set up the way your crew works rather than from a fixed package. Building the cage usually takes about 3.5 weeks to fit our production schedule. Once the cage and equipment are ready, the install itself is typically done in a day, so allow around 4 weeks in total, depending on the design. If you have your own installer, we can ship the cage Australia-wide instead.

Traffic control ute fitted by UAGS with a racking cage, arrow board and amber beacons lit
Cage, arrow board and lighting fitted in-house at Bayswater North.

7. Who designed the cage, and who backs it?

Racking cages can look similar from the outside, and some fabricators now copy existing layouts. Before you buy, ask who designed the cage, what it is built from and who supports it if the layout needs changing later.

UAGS cages are fully welded from 25 x 25 x 1.6mm SHS DuraGal steel with cold galvanising applied to the welds, and carry a 2-year limited warranty on the welded fabrication from UAG Services Pty Ltd. UAGS started in 2009 alongside Matt Calvi's own traffic management business, and we have been building racking cages for more than 15 years. Genuine UAGS cages are only supplied by UAGS.

UAGS Design 16 traffic racking cage with T-top bollard storage
For bollard work
Racking Cage Design 16

Design 7 front section plus storage for 30 T-top bollard stems and an enclosed storage box.

Frequently asked questions

How much does a traffic control racking cage cost?

UAGS standard designs are $2,170 + GST for Design 7, $2,480 + GST for Design 21 and $2,650 + GST for Design 16. Custom cages, fitting and freight are quoted separately, and trade accounts get trade pricing.

Can you design a cage for my vehicle?

Yes. We have more than 50 cage designs and draw every cage in-house in CAD. We either select a design that suits your vehicle and equipment or design a new one, and you see the CAD drawing before it is built.

How long does a full traffic control vehicle fit-out take?

Allow around 4 weeks in total, depending on the design. Most of that is building the cage, which usually takes about 3.5 weeks to fit our production schedule. Once the cage and equipment are ready, the install is typically done in a day. If we have a suitable cage in stock it can be quicker, so contact us for current lead times.

Can a racking cage go on a truck as well as a ute?

Yes. Our cages mount to ute and truck trays. Fitment depends on the tray size and the equipment setup, so send us your tray measurements before ordering.

Does a racking cage make my vehicle compliant for traffic control work?

No. A cage is a storage and deployment system only. Vehicle fitment, equipment selection and operational requirements should be confirmed against your traffic management plan, project requirements and applicable road authority conditions.

Planning a traffic control vehicle fit-out?

Send us the vehicle, the tray size and what the crew needs to carry. We will select or design the right cage and quote the full fit-out.

See our cages and fit-outs →

Or call 03 8750 0926. Trade pricing available for traffic control companies.

Previous Next