B Class LED Arrow Board Single Sided

The B Class LED Arrow Board Single Sided is a vehicle-mounted B Class LED traffic control arrow board used for rear-facing directional guidance and hazard warning on traffic control vehicles, civil fleet vehicles, utility vehicles, contractor vehicles and temporary traffic management vehicle fitouts. It is used where traffic approaching from behind the vehicle needs clear directional or caution information during roadworks, lane closures, mobile works, roadside works, utility works and civil works.

This arrow board (NAE model NAE-ABB, manufactured by National Arrow & Emergency) is TfNSW Type Approved as a Type B illuminated flashing arrow sign under TfNSW specification TSI-SP-060, certificate ITS-TAN000123. TSI-SP-060 requires illuminated flashing arrow signs to comply with AS 4192:2006, except where TSI-SP-060 varies it. The NAE-106 LED lamps were tested for luminous intensity, axes and colour by a NATA-accredited laboratory. Type Approval does not make a vehicle, worksite, traffic management plan, traffic guidance scheme or traffic setup compliant on its own. Product selection, installation and use should be confirmed against the supplied product documentation, current standards, project requirements, applicable traffic management documentation and road authority conditions.

The arrow board may be fitted to a suitable cabin rack, traffic control cage, tray headboard, tray-mounted frame, rear tray structure or other compatible vehicle mounting structure. Final mounting must be confirmed against the vehicle setup, mounting structure, project requirements and applicable traffic management documentation. We fit arrow boards at our Bayswater North depot in Victoria. Contact us for a fitment quote. Installation should be carried out by a competent installer.

The single-sided board has a 1500mm x 770mm display area, a 1545mm x 770mm mounting footprint and 15 LED clusters with luminous intensity greater than 700 cd. Display modes include Arrow Left, Arrow Right, Double Arrow and Hazard, with Hazard mode used as the non-directional warning / flashing corner mode. The flash rate is 35 to 45 cycles per minute. The Type Approval conditions are wind Region A, Terrain Category 2, and a maximum viewing distance of 860m.

The in-cabin controller has illuminated momentary push buttons, a function display and a swivel mounting bracket. Controller buttons include On/Off, Work Light, Beacon, Raise, Lower, Arrow Left, Arrow Right, Double Arrow and Hazard. The buttons light green for standby / ready and red for active functions. The electric actuator allows the board to be raised and lowered from inside the cabin.

The arrow board is supplied standard with a 12V DC actuator, with a 24V DC actuator available on request for suitable 24V vehicle systems. Confirm the required vehicle voltage before ordering. The integrated light sensor supports automatic dimming for day and night operation. The system includes short-circuit protection, solid-state circuitry, low-voltage monitoring, reverse polarity protection, over-voltage protection and fail-safe behaviour that defaults to Hazard mode during communication loss or low-voltage fault.

The enclosure is IP45 rated (sign board and LED lamp optical chamber) and uses a weather-resistant vented design to assist with internal air movement and condensation management. The product is assembled in Australia using locally manufactured structural components with imported electrical systems and actuator hardware, supporting practical servicing and integration into UAGS traffic control vehicle fitouts.

Bulky freight item. Checkout shows live carrier rates, which can be high for regional and remote deliveries. Before ordering for a remote area or in bulk, contact us for a freight quote and we will arrange the most economical option.

• Single-sided vehicle-mounted B Class LED traffic control arrow board
• Rear-facing directional display for traffic approaching from behind the vehicle
• 1500mm x 770mm display area with 1545mm x 770mm mounting footprint
• 15 LED clusters with luminous intensity greater than 700 cd
• Display modes include Arrow Left, Arrow Right, Double Arrow and Hazard
• Hazard mode operates as the non-directional warning / flashing corner mode
• 35 to 45 cycles per minute flash rate
• In-cabin controller with illuminated momentary push buttons and swivel mounting bracket
• Controller buttons for On/Off, Work Light, Beacon, Raise, Lower, Arrow Left, Arrow Right, Double Arrow and Hazard
• Illuminated controller feedback with green for standby / ready and red for active functions
• Electric actuator allows raise and lower operation from inside the cabin
• 12V DC actuator supplied as standard, with 24V DC actuator available on request for suitable 24V vehicle systems
• Integrated light sensor for automatic dimming during day and night operation
• IP45 rated weather-resistant vented enclosure to assist with internal air movement and condensation management
• Short-circuit protection, solid-state circuitry, low-voltage monitoring, reverse polarity protection and over-voltage protection
• Fail-safe behaviour defaults to Hazard mode during communication loss or low-voltage fault
• Accessory outputs for compatible beacons and rear-facing work lights
• Supplied with mounting brackets, actuator, controller, cabling, accessory patch cables, fuse holder, 23A MIDI fuses and beacon mounting plates
• Fitment available at our Bayswater North depot in Victoria, quoted separately
• Designed for wind Region A, Terrain Category 2, and a maximum viewing distance of 860m (Type Approval conditions)
• TfNSW Type Approved Type B arrow sign, certificate ITS-TAN000123 (NAE model NAE-ABB)
• NAE-106 LED lamps tested by a NATA-accredited laboratory
• Assembled in Australia using locally manufactured structural components with imported electrical systems and actuator hardware

This warranty is given by UAG Services Pty Ltd (ABN 20 508 692 637), Gate 2, 7 Royan Place, Bayswater North VIC 3153. Phone 03 8750 0926, email sales@uags.com.au.

UAG Services warrants the Single Sided B Class LED Arrow Board against defects in materials and workmanship under normal use, for the periods below from the date of purchase.

• LED lamps (LED clusters): 5 years. A claim is valid if 9 or more individual LEDs in a cluster (each cluster has 68 LEDs) fail to light under normal operating conditions, or if light output drops by 25% or more.
• Electronics and hardware: 2 years. Covers the in-cabin controller, arrow board electronics and internal modules including controller cards, the actuator (12V or 24V), mounting hardware and the enclosure.

How to make a claim. Contact UAG Services on 03 8750 0926 or sales@uags.com.au before returning or repairing anything. Provide proof of purchase (for example the invoice or delivery docket), the serial number and manufacture date from the NAE identification plate on the rear face, a description of the fault, and photos where possible. UAG Services will assess the claim with the manufacturer, National Arrow & Emergency (NAE), and may ask for the product, or the affected part, to be inspected or tested. Where the claim is accepted, UAG Services will repair or replace the defective component.

How faults are fixed. Most faults can be diagnosed remotely by UAG Services with NAE support, and the replacement part is sent to you. Warranty repairs are usually electrical parts: the actuator, an LED cluster, a controller card or an in-cabin controller.

Costs of claiming. UAG Services sends warranty replacement parts free of charge. Warranty labour is also free of charge when the work is carried out by UAG Services at our Bayswater North depot. Where a product or part needs to be returned for assessment, the customer pays the return freight to UAG Services, unless the Australian Consumer Law requires otherwise. The arrow board is a bulky item, so contact UAG Services before sending anything back. Labour for removing and refitting the arrow board elsewhere, or by another installer, is not covered by this warranty unless approved in writing by UAG Services beforehand, except where the Australian Consumer Law requires otherwise.

What is not covered. This warranty does not cover faults or damage caused by:

• abuse, misuse, collision or impact
• incorrect installation, or installation or repair by someone other than a competent installer
• water ingress through unsealed wiring, or through an actuator installed with the motor below the cable entry
• modifications to wiring, connectors or software not authorised by UAG Services
• non-genuine replacement parts or accessories

Consumables and fuses are not covered unless the failure results from a product defect.

Repairs and service. There are no user-serviceable components in the arrow board or controller. Repairs to internal electronics, wiring looms, actuators or signal connectors must be carried out by a competent installer, after contacting UAG Services. Faults caused by unauthorised repairs or modifications are not covered.

Your rights under the Australian Consumer Law. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits of this warranty are in addition to your other rights and remedies under the law in relation to the goods, and do not limit or exclude them. Nothing in this warranty excludes, restricts or modifies any right or remedy you have under the Australian Consumer Law.