380mm 42W Amber LED Magnetic Warning Minibar

The LED Autolamps LB380ACMM magnetic amber warning minibar provides 360-degree amber hazard warning from the vehicle roof without permanent installation. It suits utes, support vehicles, pool and hire vehicles, and any fleet where warning lighting needs to move between vehicles or be fitted for a single job.

The bar mounts with a magnetic suction cup base on a clean, flat section of roof, positioned parallel to the ground. The supplier rates the magnetic mount for temporary use at speeds not exceeding 100km/h, and states magnetic warning lamps are not designed for permanent use on moving vehicles - use on a moving vehicle is at the operator's discretion. For a permanent installation, LED Autolamps offers a four-point adjustable mounting feet kit (part 246BKT) as an accessory, or consider a fixed-mount bar such as the 744mm 72W Amber LED Warning Lightbar.

Power and control run through a 3m cable with a power plug, with the on/off and flash pattern selection switch built into the plug. There is no permanent wiring: plug in, place the bar and it is operating, which is what makes this model practical for vehicle-to-vehicle transfer.

Light output comes from 42 x 1 watt LEDs behind a clear polycarbonate lens, producing 360-degree omnidirectional amber output. There are 18 selectable flash patterns, from rotating and single/double/quad flash modes through to hyper-flash and steady burn. The supplied product data identifies pattern 9 (Quad, all LEDs) as the SAE J845 Class 1 compliant pattern and patterns 12 to 15 (the 2Hz modes) as the ECE R65 patterns.

Multivolt 10-30V DC operation suits both 12V and 24V vehicle electrical systems. Current draw is 2.51A at 13.8V DC.

The ABS base and polycarbonate lens carry an IP67 ingress protection rating with an operating temperature range of -40°C to +60°C, suiting exposed roof positions subject to dust and weather.

The supplied product data lists ECE R65 and ECE R10 approval and SAE J845 Class 1 compliance. These certifications relate to light output performance and electromagnetic compatibility as per the supplied product data.

The LB380ACMM is the mid-size magnetic option in the LED Autolamps range. For a smaller magnetic bar, see the 246mm Amber LED Magnetic Warning Minibar.

Commonly used on traffic control support vehicles, civil fleet vehicles, utility vehicles and hire or pool vehicles. Vehicle lighting requirements may vary by vehicle type, registration category, jurisdiction and intended use. Vehicle warning systems support visibility but do not replace a traffic management plan or traffic guidance scheme.

• 42 x 1W LED Configuration: amber output through a clear polycarbonate lens with 360-degree omnidirectional coverage
• Magnetic Suction Cup Mounting: no-drill temporary mounting on a clean, flat roof section; supplier-rated for temporary use at speeds not exceeding 100km/h
• Plug-In Operation: 3m cable with power plug, with the on/off and flash pattern selection switch built into the plug - no permanent wiring
• 18 Flash Patterns: pattern 9 (Quad, all LEDs) is the SAE J845 Class 1 compliant pattern; patterns 12-15 (2Hz modes) are the ECE R65 patterns per supplied data
• Multivolt Operation: 10-30V DC input suits 12V and 24V vehicle electrical systems
• IP67 Construction: ABS base and polycarbonate lens, rated -40°C to +60°C
• Certified Output: supplied product data lists ECE R65 and ECE R10 approval and SAE J845 Class 1 compliance
• Fixed-Mount Option: LED Autolamps 246BKT four-point adjustable mounting feet kit available as an accessory for permanent installation
• Fleet Application: suits support vehicles, pool and hire vehicles, and crews moving one bar between vehicles

Manufacturer Warranty - 5 Years
This product is covered by the manufacturer's warranty of 5 years against defects in materials and workmanship under normal use, in accordance with the manufacturer's standard warranty terms.

This warranty does not cover normal wear and tear, weathering or UV degradation, accidental or impact damage, incorrect or unauthorised installation, unauthorised modification, or use outside the product's stated operating conditions. Installation should be carried out by a qualified auto electrician; damage caused by DIY wiring is not covered.

To make a warranty claim, contact UAG Services Pty Ltd (Gate 2, 7 Royan Place, Bayswater North VIC 3153) at sales@uags.com.au or (03) 8750 0926 with your order reference, a description of the fault and photos of the product. UAG Services Pty Ltd will refer the claim to the manufacturer or authorised representative where required. Return shipping costs are handled in accordance with the UAGS Returns Policy unless otherwise required under Australian Consumer Law.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is provided in addition to these rights and does not limit or exclude them.