B Class LED Arrow Board Double Sided

The B Class LED Arrow Board Double Sided is a double-sided vehicle-mounted B Class LED traffic control arrow board used where directional guidance or hazard warning display is required from both the rear and front of a traffic control vehicle. It is suited to traffic control vehicles, convoy vehicles, mobile works vehicles, civil fleet vehicles, utility vehicles, contractor vehicles and temporary traffic management vehicle fitouts where traffic may approach or view the vehicle from more than one direction.

The double sided board (NAE model NAE-ABDB, manufactured by National Arrow & Emergency) has its own TfNSW Type Approval as a Type B illuminated flashing arrow sign under TfNSW specification TSI-SP-060, certificate ITS-TAN000124. TSI-SP-060 requires illuminated flashing arrow signs to comply with AS 4192:2006, except where TSI-SP-060 varies it. It uses the same board body, NAE-106 LED lamps and NAE-CTL-V2 controllers as the single sided board, with 15 more LED clusters, a second in-cabin controller, a second controller cable and a second internal controller card for the forward-facing display. The NAE-106 LED lamps were tested for luminous intensity, axes and colour by a NATA-accredited laboratory.

The double-sided configuration should be confirmed against the supplied product documentation, current standards, project requirements, applicable traffic management documentation and road authority conditions. Product selection, installation and use do not make a vehicle, worksite, traffic management plan, traffic guidance scheme or traffic setup compliant on their own.

The arrow board may be fitted to a suitable cabin rack, traffic control cage, tray headboard, tray-mounted frame, rear tray structure or other compatible vehicle mounting structure. Final mounting must be confirmed against the vehicle setup, mounting structure, project requirements and applicable traffic management documentation. We fit arrow boards at our Bayswater North depot in Victoria. Contact us for a fitment quote. Installation should be carried out by a competent installer.

The double-sided board has a 1500mm x 770mm display area, a 1545mm x 770mm mounting footprint and 30 LED clusters total, with 15 LED clusters per side. Display modes include Arrow Left, Arrow Right, Double Arrow and Hazard, with Hazard mode used as the non-directional warning / flashing corner mode. The flash rate is 35 to 45 cycles per minute and luminous intensity is greater than 700 cd. The Type Approval conditions are wind Region A, Terrain Category 2, and a maximum viewing distance of 860m.

The system includes two in-cabin controllers with illuminated momentary push buttons and function displays. Both fit one dual controller mounting plate, side by side or one above the other, on a single swivel bracket. The rear (main) controller runs the rear-facing display and all board functions: On/Off, Work Light, Beacon, Raise, Lower, Arrow Left, Arrow Right, Double Arrow and Hazard. The FRONT controller runs the forward-facing display only: On/Off, Arrow Left, Arrow Right, Double Arrow and Hazard. The buttons light green for standby / ready and red for active functions. The electric actuator allows the board to be raised and lowered from inside the cabin.

The two displays work independently, each with its own controller, controller cable and internal controller card. There is no interlock between them, so the operator must check that the two faces do not show conflicting displays. The FRONT controller carries the warning "Be aware of conflicting displays".

Both internal controller cards are housed within the same board body, with service access through two access panels on the rear-facing side. Because the double sided board uses the same board body, LED lamps, controllers and controller cards as the single sided board, many core service parts are interchangeable to support fleet servicing, spare parts management and long-term maintenance for customers running mixed arrow board fleets.

The arrow board is supplied standard with a 12V DC actuator, with a 24V DC actuator available on request for suitable 24V vehicle systems. Confirm the required vehicle voltage before ordering. The integrated light sensor supports automatic dimming for day and night operation. The system includes short-circuit protection, solid-state circuitry, low-voltage monitoring, reverse polarity protection, over-voltage protection and fail-safe behaviour that defaults to Hazard mode during communication loss or low-voltage fault.

The enclosure is IP45 rated (sign board and LED lamp optical chamber) and uses a weather-resistant vented design to assist with internal air movement and condensation management. The product is assembled in Australia using locally manufactured structural components with imported electrical systems and actuator hardware, supporting practical servicing and integration into UAGS traffic control vehicle fitouts.

Bulky freight item. Checkout shows live carrier rates, which can be high for regional and remote deliveries. Before ordering for a remote area or in bulk, contact us for a freight quote and we will arrange the most economical option.

• Double-sided vehicle-mounted B Class LED traffic control arrow board
• Rear-facing and forward-facing display capability from the same board body
• 1500mm x 770mm display area with 1545mm x 770mm mounting footprint
• 30 LED clusters total, with 15 LED clusters per side
• Luminous intensity greater than 700 cd
• Display modes include Arrow Left, Arrow Right, Double Arrow and Hazard
• Hazard mode operates as the non-directional warning / flashing corner mode
• 35 to 45 cycles per minute flash rate
• Two in-cabin controllers with illuminated momentary push buttons, one for the rear-facing display and one for the forward-facing display
• Front and rear displays work independently, and the FRONT controller carries a conflicting displays warning
• Both controllers fit one dual mounting plate on a single swivel bracket, side by side or one above the other
• Rear (main) controller buttons for On/Off, Work Light, Beacon, Raise, Lower, Arrow Left, Arrow Right, Double Arrow and Hazard
• Illuminated controller feedback with green for standby / ready and red for active functions
• Both internal controller cards housed within the same board body
• Service access through two access panels on the rear-facing side
• Same board body, LED lamps and controllers as the single sided model
• Double sided configuration adds 15 LED clusters, a second controller and controller cable, and a second internal controller card for the forward-facing display
• Many core service parts are shared or interchangeable between the single-sided and double-sided versions
• Electric actuator allows raise and lower operation from inside the cabin
• 12V DC actuator supplied as standard, with 24V DC actuator available on request for suitable 24V vehicle systems
• Integrated light sensor for automatic dimming during day and night operation
• IP45 rated weather-resistant vented enclosure to assist with internal air movement and condensation management
• Short-circuit protection, solid-state circuitry, low-voltage monitoring, reverse polarity protection and over-voltage protection
• Fail-safe behaviour defaults to Hazard mode during communication loss or low-voltage fault
• Accessory outputs for compatible beacons and rear-facing work lights
• Supplied with mounting brackets, actuator, controllers, cabling, accessory patch cables, fuse holder, 23A MIDI fuses and beacon mounting plates
• Fitment available at our Bayswater North depot in Victoria, quoted separately
• TfNSW Type Approved Type B arrow sign, certificate ITS-TAN000124 (NAE model NAE-ABDB)
• Designed for wind Region A, Terrain Category 2, and a maximum viewing distance of 860m (Type Approval conditions)
• NAE-106 LED lamps tested by a NATA-accredited laboratory
• Assembled in Australia using locally manufactured structural components with imported electrical systems and actuator hardware

This warranty is given by UAG Services Pty Ltd (ABN 20 508 692 637), Gate 2, 7 Royan Place, Bayswater North VIC 3153. Phone 03 8750 0926, email sales@uags.com.au.

UAG Services warrants the Double Sided B Class LED Arrow Board against defects in materials and workmanship under normal use, for the periods below from the date of purchase.

• LED lamps (LED clusters): 5 years. A claim is valid if 9 or more individual LEDs in a cluster (each cluster has 68 LEDs) fail to light under normal operating conditions, or if light output drops by 25% or more.
• Electronics and hardware: 2 years. Covers both in-cabin controllers, arrow board electronics and internal modules including controller cards, the actuator (12V or 24V), mounting hardware and the enclosure.

How to make a claim. Contact UAG Services on 03 8750 0926 or sales@uags.com.au before returning or repairing anything. Provide proof of purchase (for example the invoice or delivery docket), the serial number and manufacture date from the NAE identification plate on the rear face, a description of the fault, and photos where possible. UAG Services will assess the claim with the manufacturer, National Arrow & Emergency (NAE), and may ask for the product, or the affected part, to be inspected or tested. Where the claim is accepted, UAG Services will repair or replace the defective component.

How faults are fixed. Most faults can be diagnosed remotely by UAG Services with NAE support, and the replacement part is sent to you. Warranty repairs are usually electrical parts: the actuator, an LED cluster, a controller card or an in-cabin controller.

Costs of claiming. UAG Services sends warranty replacement parts free of charge. Warranty labour is also free of charge when the work is carried out by UAG Services at our Bayswater North depot. Where a product or part needs to be returned for assessment, the customer pays the return freight to UAG Services, unless the Australian Consumer Law requires otherwise. The arrow board is a bulky item, so contact UAG Services before sending anything back. Labour for removing and refitting the arrow board elsewhere, or by another installer, is not covered by this warranty unless approved in writing by UAG Services beforehand, except where the Australian Consumer Law requires otherwise.

What is not covered. This warranty does not cover faults or damage caused by:

• abuse, misuse, collision or impact
• incorrect installation, or installation or repair by someone other than a competent installer
• water ingress through unsealed wiring, or through an actuator installed with the motor below the cable entry
• modifications to wiring, connectors or software not authorised by UAG Services
• non-genuine replacement parts or accessories

Consumables and fuses are not covered unless the failure results from a product defect.

Repairs and service. There are no user-serviceable components in the arrow board or controller. Repairs to internal electronics, wiring looms, actuators or signal connectors must be carried out by a competent installer, after contacting UAG Services. Faults caused by unauthorised repairs or modifications are not covered.

Your rights under the Australian Consumer Law. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits of this warranty are in addition to your other rights and remedies under the law in relation to the goods, and do not limit or exclude them. Nothing in this warranty excludes, restricts or modifies any right or remedy you have under the Australian Consumer Law.